Description Ridge Fixing Bracket for use with Ceiling Fans• This bracket is used for fixing a ceiling fan to a conservatory roof that does not have a solid fixing point on the underside of the ridge ie. DESCRIPTION: This hanging bracket can be installed in a ceiling joist or structure capable of carrying a load of 35 lbs. Do not do it wack-a-dack merely because doing it correctly is too hard -- that's what people are warning you off from.

b) You can purchase an Advance Replacement unit, which we send to you, this allows you to have the units exchanged at your own convenience. EDIT: I noticed the packaging says to use a box rated for a 35lb or less fan, so this is not a very heavy fan. Place one end of the block in the old junction box and tap the other end of the block with the hammer until the box pops free in your ceiling cavity. You can change your choices at any time by visiting Cookie preferences, as described in the Cookie notice.Of course not, but in those tiny number of cases, you'll find we pull all of the stops out to put things right for you. UPS (if available): The US American courier was established in the first decade of the 20th century. How to Install a Ceiling Fan Bracket | Here's how to remove an old light and install a ceiling fan bracket so you can properly install your new ceiling fan.

Is there some way I can brace or reinforce this from above, up in the attic, so I don't have to open (unseal) everything up again? You cut away the drywall to match the circular outline of the box and you would have to patch the old hole. The correct paperwork can then be sent and these photographs will ensure that replacements or refunds can then be processed with a minimum of delay. That support is probably an old gas line (pre electricity) I say this because of the length you described. Other brands, use screws to tighten the brace which does not drive the teeth into the studs - major fail.It would not be long until the successful company began to establish subsidiaries all over the world. New: A brand-new, unused, unopened and undamaged item in original retail packaging (where packaging . In some cases, we may offer a partial refund to cover the remaining part of any existing warranty rather than a replacement. However, unless this is an open ceiling, that will (a) have the box dropping below the finished ceiling and (b) not look very nice. You also get the nice advantage of more flexibility for placement of the fan, though if you are making use of an existing hole in the ceiling then that is a non-issue.

Even when purchasing a single heater, it will be delivered on a pallet in an attempt to ensure no damage is caused during transit due to the weight of the unit and also the weight of the bricks to be fitted into the unit on installation. Read more about the condition New: A brand-new, unused, unopened and undamaged item in original retail packaging (where packaging is applicable). Not sure if the head will be on show, if so you might want to get a pack of chrome screw caps to cover the screw head, again from our host. If for some reason you cannot use a "brace" between two studs, you could use a saddle box around this stud and hang the fan directly under the stud. I am wondering do I need to reinforce the joists at all or is this sufficient to hang a ceiling fan of average weight?A ceiling fan support brace reinforces the structural integrity of a junction box so the fan stays in place. A direct mounting on a dropped ceiling without any additonal support in-between could lead to resonance sounds or an unstable hold of the fan on the ceiling, because the carrying material does not offer enough stability in this case.

And then a ‘split lock washer’, this split section applies pressure to underside of screw head and locks it in place. This bracket is used for fixing a ceiling fan to a conservatory roof that does not have a solid fixing point on the underside of the ridge ie. The 103 third parties who use cookies on this service do so for their purposes of displaying and measuring personalized ads, generating audience insights, and developing and improving products. A 5x50mm is on the biggish size for holding up a light fitting, it tends to be 4mm screws I use at a length appropriate to grip into the timber.After spending his college summers pouring concrete and building decks, Harrison Kral decided to find a way to put his insider knowledge of construction to use…. If the item comes direct from a manufacturer, it may be delivered in non-retail packaging, such as a plain or unprinted box or plastic bag. We are no longer supporting IE (Internet Explorer) as we strive to provide site experiences for browsers that support new web standards and security practices.