Start spraying or rolling the stripper along edges first and then fill up the entire remaining area, During application, make sure to keep the applied surface wet with a garden hose water mist or spray. Caustic wood stain removers work by dissolving the finish and converting it into another substance. They usually consist of strong bases, which are corrosive.

Give it a good scrub with a stiff brush. Scrub along the grooves and also across them to help loosen the old coating. Pour on some water and keep scrubbing. This will help lift the finish completely off. You can use many products to remove these stains, from vinegar to bleach. Just remember never to mix chemicals when cleaning, even when you’re outdoors.

Help – I don’t know what coating is on my deck!

No matter which application method you go with, keep the advice of Cohoon in mind. When using an oxygen-based cleaner, in particular, look for "at least 20 percent" of your ingredients to be peroxide or another suitable oxidation agent, since that's ultimately what will treat your stain and help remove it.

Due to its potent formula, it’s capable of removing latex and oil-based paint along with lacquer, shellac, epoxy, and floor finishes. You can strip up to 25 square feet with each gallon. To use this product, pour or brush the wood stain remover onto the surface and wait a couple of minutes. Then, scrape off the layers of stain, wipe away with a cloth, and you’re done. (You can use a wire brush to scrub stubborn areas.)

How To Remove Oil-Based Stain From Wood

If you’d like, you can sand the wood surface. Allow the wood to dry for at least 24 hours first. Wear safety goggles and a face mask. Then, sand the dry surface using consistent pressure. Topmost important rule: read and follow the manufacturer’s instructions to the letter for best results.

Puracy Stain Remover: In general, Puracy products have performed adequately when we've tried them before. When considered in a head-to-head scenario, though, the stain remover's performance didn't measure up to other options. It earned a low score for effectiveness and ease of use, since our tester found that the spray bottle didn't work well. Stains weren't removed as efficiently as we hoped, and our tester noted that other products are better at removing grass and marker stains. Remember to wear your heavy-duty gloves, goggles, and protective boots before you begin the heavy-duty task at hand. An old stain needs to be removed instead of coating it with another layer of stain. If you ignore the stripping stage, the new stain will develop bubbles and blisters since the protective stain film no longer keeps the molds and moisture at bay. Tools and materialsIf your wood stain remover consists of potent chemicals, it could be hazardous to both you and your family’s health. Look for a wood stain remover that’s safe for indoor use if you’ll be using it inside your home. Kathy Cohoon, franchise owner at Two Maids & A Mop, shared expertise on how to approach laundry stain removal and what to look for when purchasing a stain fighter. Leave it to work for around 30 minutes, keeping an eye out for any patches that start to dry out. If this happens, re-apply on these areas. Solvents work by dissolving the old finish with chemicals. Examples of solvents in wood stain removers include alcohol, acetone, and toluene. Solvents are some of the only wood stain removers that can dissolve paint. Unfortunately, they’re usually the most toxic. Once removed, rinse thoroughly with lots of fresh clean water, using the highest pressure from the water source available or via the use a pressure washer at 500-1000 psi (35-70 bars).

How do they compare? All of these products are top-performing wood strippers, though they each have differences which may better suit specific requirements. The only two of these strippers that are intended for use on solid paint are the Dumond Chemicals Smart Strip Advanced Paint Remover and the Woodrich Heavy Duty Wood Stripper and Wood Cleaner. The remaining three are intended for use on clear varnish, sealers, and stains, or semi-transparent stains. Work in small sections and be careful, as it can be quite slippery when it’s working. It doesn’t blister or fizz but don’t worry, it’s doing the job. If you working on several projects and need to remove stain and paint, choose a versatile product. What are the different types of wood stain removers? If your wood is coated with wood oils, whether that be teak oil, linseed oil or another type of wood oil we’d first and foremost recommend you strip them using Aquanett. It’s designed specifically for removing wood oils and it’s a gel formula so it’s easy to use. This stripper is not for use on solid paints or acrylic-based stains. It is recommended for use as the first step in a series of wood refinishing steps and should be followed up with a wood brightener to neutralize the pH of the wood.Make sure you hose off everything. You might need to hose off areas more than once in some cases. When the water dries, it will leave a grimy film in some areas if you don’t. There are a few different types of wood stain removers, and we’ll discuss each of them in greater detail below: After 30 minutes scrape the surface with something sharp, like a paint scraper, to see if it’s worked. You should see the old coating lifting as you scrape. If not, put a bit more on and leave for another 10-15 minutes. You can also use a random orbital sander to eliminate every lingering stain from your wood. Set up your sander for removing paint and begin sanding using a coarse-grit sandpaper. Finish with fine-grit sandpaper to buff the wood once you no longer have any stains left on the wood.