Do not place the battery into regular rubbish bins. Strictly follow your local disposal and recycling regulations of batteries. Try and charge / discharge the battery completely every so often (once every 20 or so uses) to ensure that the management software in the battery can configure itself successfully. If DJI go tells you to update the batteries firmware great if not connect your drone to DJI assistant and do a firmware refresh with every battery you own. 10. Factory reset your drone The P3 batteries are protected by a smart charge and discharge function built into the battery itself. DJI smart chargers stop the current from reaching the battery when there is too much of it to avoid damage.

Very carefully and gently disconnect the balancing plug/loom(Lithium Polymer balance plug) to the IC. When using the battery charging hub, the batteries will be charged in sequence according to their power levels, from high to low. When used with the DJI 30W USB-C charger, the battery charging hub can fully charge one battery in approximately 56 minutes and one Intelligent Flight Battery Plus in approximately 78 minutes. After the battery is fully charged, the corresponding LEDs will change to solid green. The battery can be disconnected from the charging hub when charging is complete. After flying - give the battery at least 10 minutes to cool down before charging. The heat can build up in LiPO batteries so ensure you let the temperature drop before starting to charge, which can increase temperatures.

Lithium Polymer Battery Fix

Fully charge the Intelligent Flight Battery before each use. It is recommended to use the charging devices provided by DJI, such as DJI Mini 3 Series Two-Way Charging Hub, DJI 30W USB-C Charger, or other USB Power Delivery chargers. Please follow the instructions provided below to properly charge the Intelligent Flight Battery and remote controller:

The Lithium Polymer batteries are fragile and easily damaged which can cause many problems for the pilots of the drone that uses Lithium Polymer batteries. Intelligent Flight batteries Taking care of the battery is not difficult. But if you don’t do it correctly, it is unlikely that the battery will last very long. Firstly, avoid using the battery if it shows signs of damage. The swelling sign is a definite indicator of a problem since it shows that the battery is leaking. Do not plug the battery in the charger and go to attend to other business. Ensure that you keep your eye on the chargers’ status bar. It will always indicate the charging level. Keeping an eye on it ensures that you don’t overcharge the battery.Battery damage can be caused by age, physical damage, or poor battery maintenance and it might be time to buy another battery

The DJI Phantom 3 intelligent flight battery supports input of 12V 1.5 A / 9V 2A / 5V 3A. 6. Overheating Charge and discharge the battery completely once every 20 charge/discharge cycles. Discharge the battery until there is less than 8% power or until it can no longer be turned on, then recharge it to the maximum capacity. This power cycling procedure will optimize the battery life. After you hand it to DJI it can take up to 15 days till they send a replacement, and it can take longer if you don’t live in the United States Turn the battery on and plug it in, The flat turned on the battery should be flashing red before connection.Dispose of the battery into specific recycling boxes only after a complete discharge. Do not place the battery into regular rubbish bins. Strictly follow your local disposal and recycling regulations of batteries. Using the alligator clips, connect the cables directly to the cells which will side bypass the smart circuit. The Intelligent Flight Batteries offer super-long flight times of up to 30 minutes as well as LEDs on the battery that show the pilot the status of the remaining power left in the battery in real-time. Once the voltmeter reaches above 20.00V, you can reconnect the balancing plug and recharges the battery as per normal.

After the batteries are installed, the charging hub can supply power to external devices via the USB-C port, such as remote controllers or mobile phones.During the charging process, the battery level LEDs of both the Intelligent Flight Battery and the remote controller will blink sequentially, indicating the current battery level. After fully charged, the four Battery Level LEDs emit a solid light. Please disconnect the aircraft and charger. Unfortunately, when your Phantom 3 battery stops charging, you cannot get outdoors and enjoy flying your drone. Such a battery may charge after a little bit of finagling, or it may never charge again. In the latter case, you will have no option other than to buy a new battery. Read on to see why the Phantom 3 battery may refuse to charge and what you can do to fix the problem. Poor Storage and Maintenance DJI drones use Intelligent Flight Batteries which are basically just Lithium Polymer batteries but with the only difference being that this type of battery prioritizes safety and has a lot more technology to help with that. Connect the battery to the charger and the Battery Level LEDs in an array blink successively. The charging time for one battery is approximately 1 hour and 35 minutes. After fully charged, the four Battery Level LEDs are off. Detach the charger after charging is complete.