There is a very slight hum coming from my turntable. I only know this, as when I approach my hifi to change records. I can hear it. I've never noticed it when playing music. Would such a circuit affect ambient noise in your room? - absolutely not, unless your transformer is humming and you can hear it! A DC filter would stop that, for sure. The new power conditioning accessory "Sparkz TC3" from Ansuz Acoustics is designed to reduce noise in the power supply chain thanks to various technologies, and thus improve the sound of hi-fi components. The device is designed for use with a single audio or AV system component. Audiolab recommends that it should be used with the integrated amp or power amp component within your system to obtain the most significant benefit.

Many many years ago. I replaced my cheap bell wire with a QED79 cable. Connected it up to my Pioneer SA608 and Kef Celeste III speakers. Didn't hear a difference. The science absolutely guarantees that removing DC improves a transformers ability to do its job, and therefore it is very likely to make an audible difference in audio equipment. I bet your speakers were designed on a clean mains supply, for sure. Prices valid in stores (all including VAT) until close of business on 29th November 2023. (Some of these web prices are cheaper than in-store, so please mention that you've seen these offers online.)I/O's are not decoupled so in almost any ofthe designs I have scrutinized, interconnects shield noise is landed right on to the PCB instead of grounded to chassis. The stray infects the so delicate 0 volt ref voltage to numerous IC's including the DAC chip. Do not take just my word for it, it is a friend of mine, studio technician, Master of Science educated, at least 40 years in the profession, who rebuild DAC's like dCS, but also cheaper versions like Topping D90SE, who claims that ground ref is is a design flaw in it self as are many other areas. The ground is then also challanged by the standard procedure of soldering e.g. pin1 but also shields in USB's, I2S UI, etc in the PCB. The PCB ground should not be used to land noise from cable shield in my opinion. So when decoupling, you should be able to trust the ground you decouple to., but you cannot. One thing so often overlooked is the use of filter and buffert electrolythic caps. They are in the analogue domain often soldered i pairs from the positive and negative to the ground, instaed of caring for the ground by having one twice the size directly between positive and negative only. The filter caps for purely decoupling is wired equally. Why? Some brands use local regulators some do not. In my opinion all voltage regulators should of top class with a few microvolts ripple if any, and locally, with a large buffer, zobel and decoupling almost at the same pin as it is designed to feed. Hifi grade el caps is a myth. The modern 105 degree offers in general better life expectancy and radically lowered internal losses for decoupling. Mains electricity has a fundamental influence on the audio signal as it passes through a system, from source to amp to speakers. The mains supply in a typical dwelling is subject to interference induced by a range of issues, causing the AC waveform to distort before it reaches each component and can create noise in the audio signal. This can degrade sound quality. The actual problem is not that everything should be designed as optimal as possible. It should be designed good enough. Calling it a "power strip" would not do it justice. According to the manufacturer, Chord Company's Master M6 and Studio S6 power distribution units, called PowerHAUS, can do much more than ordinary or even high-quality power strips.

Not to worry though, I’m not selling it and it’s probably not for tabletop speakers. But proven principle of physics isn’t snake oil and the principle of removing DC from an AC power supply is known to affect audio equipment and I suppose that’s all I’m trying to clarify. Audiolab's new midrange product line is said to incorporate technologies from the new 9000 flagship models and consists of an integrated amplifier, a streamer as well as a CD transport.Admittedly, it's quite a basic circuit to filter it and I've obviously never auditioned this audiolab unit but if your transformer is affected by DC, which it almost certainly will be if you have a fridge, washing machine and dish washer on your home mains, and if this circuit is correct (which I'm sure it would be), it's not snake oil to suggest that it would work. It's physics. You often do not need super low noise regulators, you often do not need the lowest possible ESR caps. They are all design choices made by requirements, availability of parts and price. You don’t ‘hear’ DC - there is no audible noise, like static or white noise. Maybe you’ll hear the transform hum a little bit that’s a vibration that you’re hearing, caused by DC. The Polish brand Ferrum launches the "Power Splitter", a matching accessory for the external power supply Hypsos, with which it is supposd to power two devices simultaneously.