Peng, J.Z. Study on the Forming, Characterization and Effection of Autoclaved Aerated Concrete Pores. Ph.D. Thesis, Chongqing University, Chongqing, China, 2011. [ Google Scholar] General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China. Thermal Insulation Determination of Steady-State Thermal Resistance and Related Properties Guarded Hot Plate Apparatus; GB/T 10294-2008; China Standard Press: Beijing, China, 2008. Calignano F, Manfredi D, Ambrosio EP, Iuliano L, Fino P (2013) Influence of process parameters on surface roughness of aluminum parts produced by DMLS. Int J Adv Manuf Technol 67(9–12):2743–2751 Ramamurthy, K.; Kunhanandan Nambiar, E.K.; Indu Siva Ranjani, G. A classification of studies on properties of foam concrete. Cem. Concr. Compos. 2009, 31, 388–396. [ Google Scholar] [ CrossRef]

Simchi A, Petzoldt F, Pohl H (2003) On the development of direct metal laser sintering for rapid tooling. J Mater Process Technol 141(3):319–328 Prechtl M, Otto A, Geiger M (2005) Rapid tooling by laminated object manufacturing of metal foil. Trans Tech 6–8:302–312 National Development and Reform Commission. Aluminum Pastes for Aerated Concrete; JC/T407–2008; China Building Industry Press: Beijing, China, 2008. Fomina, E.V.; Chulenyov, A.S.; Kozhukhova, N.I. Properties control in autoclave aerated concrete by choosing of pore forming AL-agent. Mater. Sci. Eng. 2018, 365, 321–329. [ Google Scholar] [ CrossRef]For all it sounds like a sports car, it’s really a professional quality brush designed to be super-efficient in heavier-bodied waterborne, acrylic and alkyd paints. The perfect brush for cutting in emulsion, for example! The capacity and release of paint on these T-Class rollers is superb and they’re very easy to break in, plus don’t need to be pre-conditioned thanks for the wool’s natural oil. And bearing in mind how tough sheep are, it’s no surprise that these The maximum force for the peel tests was much lower than the maximum force for Al 99.5 which is 250 N (100 MPa or 100 N/mm 2) for a cross-sectional area of 2.5 mm 2 (25 × 0.1 mm). These test results differ significantly from adhesive bonds that fail uniformly upon the application of load. When a load was applied to the brazed specimens, they showed the formation of teeth. The reason for the formation of teeth is the presence of un-bonded area indicating an absence of bond between the two foils. The teeth signify the integrity of the bond produced by CMFM. Smaller teeth indicate a better bond, whereas larger teeth signify a poor bond. The presence of un-bonded areas can be attributed to the application of insufficient force during brazing, resulting in the paste not being able to penetrate the tenacious oxide layer at the interface. The peel test proved useful in understanding the overall bond effectiveness produced by CMFM. The substrate failed by splitting in layers; therefore, the failure pattern was given the designation DF (delamination failure). 3.3 Results from dog-bone tensile test

Ministry of Housing and Urban-Rural Construction of the People’s Republic of China. Technical Specification for Application of Autoclaved Aerated Concrete; JGJ/T17-2008; China Building Industry Press: Beijing, China, 2008. Syvanen T (1996) Direct sintering of metals material and process development M.Sc. Thesis, Tampere University of Technology Jin, H.Q.; Yao, X.L.; Fan, L.W.; Xu, X.; Yu, Z.T. Experimental determination and fractal modeling of the effective thermal conductivity of autoclaved aerated concrete: Effects of moisture content. Int. J. Heat Mass Tran. 2016, 92, 589–602. [ Google Scholar] [ CrossRef] Butt J, Mebrahtu H, Shirvani H (2014) A novel rapid prototyping process for the production of metal parts, “proceedings of the second international conference on advances in civil, structural and mechanical engineering, Birmingham, pp 26–29. doi: 10.15224/978-1-63248-054-5-45A key design factor in this stripping knife is, once again, the handle. This time it’s all soft grip, ergonomincally designed to be comfortable, but also to be very tough. Yin, J.; Zhou, S.Q. A contrastive study of direct tensile strength and splitting tension strength of high performance concrete. J. Changsha Railw. Univ. 2011, 19, 25–29. [ Google Scholar] Mueller B, Kochan D (1999) Laminated object manufacturing for rapid tooling and patternmaking in foundry industry. Comput Ind 39(1):47–53 Armstrong KB (1997) Long-term durability in water of aluminium alloy adhesive joints bonded with epoxy adhesives. Int J Adhes Adhes 17(2):89–105 Da Silva LF, Carbas RJC, Critchlow GW, Figueiredo MAV, Brown K (2009) Effect of material, geometry, surface treatment and environment on the shear strength of single lap joints. Int J Adhes Adhes 29(6):621–632