I attached two photos of the area that I started to cut but stopped after few cuts because I noticed slight cutting marks (blurring) on surrounding non touched-up area. The Mirka Shark Blade is supplied in a hard wearing pouch with belt loop and with a cord to hang it around your neck if required. JB Tools Non-Affiliation Notice and Disclaimer: JB Tools holds itself out as neither the manufacturer, an affiliate of the manufacturer, or an “authorized” distributor of this product. Combined, Mirka Waterproof Sanding Rosettes and Polarstar Spot Repair Discs are available in P1500, P2000, P2500, P3000, and P5000 grades (10 rosettes per sheet).

Please include what you were doing when this page came up and the Cloudflare Ray ID found at the bottom of this page. On my previous car I tried to flat the area with wet sanding method (small piece of P2000 on the tip of pencil with rubber eraser on top) but I wasn't quite patient and tried to redo repaired area 3 times and managed to achieve strikethrough. The Mirka Shark Blade is a valuable tool designed to remove paint imperfections, runs, high spots and nibs quickly and easily. The carbide steel which the Mirka Shark Blade is made of, as used in drill bit tips, enables the edges of the Mirka Shark Blade to keep their sharpness and therefore have a longer lifetime, which then enables the blade to cut through debris for many more years. Also, you need to flat the clip after shaving off, so a slight scuff is fine as it'll probably sand out.Unfortunately we aren’t able to send parcels to these addresses at present but we are working on it. Ideal for quickly removing nibs and blemishes with minimal damage to the surrounding sound paint finish. These cookies help provide information on metrics the number of visitors, bounce rate, traffic source, etc. By purchasing this product from JB Tools, purchasers may not be guaranteed any manufacturer-provided services offered by the manufacturer of this product (including any training or technical support that may otherwise be available).

I assume that it will be much easier to "drive" denibber over the surface when you can simply place it on the surface and leave the gravity do it's part. Although it’s mainly used in the car body repair sector, it’s found a home with fine decorators who specialise in hand and spray painted furniture and fixtures. The Mirka Shark Blade Scraper / De-Nibber is capable of precisely removing dirt nibs and high spots, in a few quick passes. I found few instructional videos for Festool Denibber and how to place it to rest on the matching cord to achieve optimal cutting angle. Gently push the sharp chamfered edge against the paint blemish whilst the blade is at an almost horizontal angle to remove in one sweep.The Mirka Shark Blade is a tool designed to remove paint imperfections, runs, high spots and nibs quickly and easily.

Most purchases from business sellers are protected by the Consumer Contract Regulations 2013 which give you the right to cancel the purchase within 14 days after the day you receive the item. The Shark Blade works by simply sliding or pushing over the dirt, nib or run, similar to a razor blade but without the flexibility associated with a thin blade.There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data. It is made of carbide steel, as used in drill bit tips, which enables the edges of the Shark Blade to keep their sharpness and cut through debris for many years. Rubbing alcohol 70% for flattening by light soaking and gentle rubbing blob with cotton bud (can use 99% but 70% takes smaller amount off and can more precisely level blob). It's all too easy when sanding down a run to go through the paint layer either side, but by using this little tool you can shave off the high spot with ease. Touched up area will be, when polished, little more dull than surrounding factory clear but that is maximum visual effect you'll achieve since base coat can never be polished to level of the clear.

It is a valuable tool designed to remove paint imperfections, runs, high spots and nibs quickly and easily. Have been lurking for ages and joined forum some time back but never wrote anything since vast majority of forum population do not have much to learn from me or my "rich" experience in detailing. To better understand how it works, imagine having the cutting power of a razor, without the flexibility issues associated with a thin blade.Gathers information for WordPress by themselves, first party analytics tool about how WP services are used. Although it's mainly used in auto and marine paint repair, it's found a home with fine decorators who specialize in hand and spray painted furniture and fixtures. On other hand, haven't found any video instruction or user manual for proper Mirka Shark Blade handling. If you're not a pro painter or maybe have to spray in less than ideal conditions then you'll sometimes come up against runs,sags, or dust nibs.