Aoyue 701A++ is another Aoyue product on our list with affordable prices and multiple perfect features. This vacuum desoldering station 70-watt heating element can set a range of temperatures between 392 and 896 degrees. Digital Control and Calibrated Life Heater The desoldering station comes with a Smoke Absorber to absorb dangerous Smoke and prevent a user from harmful health impacts. Key Features: Once the solder is molten, place the tip of the desoldering pump against the solder that you want to remove.

The process of desoldering is relatively straightforward when you have the right tools to hand. The simple concept for the desoldering process revolves around applying heat, remove the component, and then clean up the solder still attached on the PCB. Some of the key features include this product that it has 2 has two lines, one for power and another for vacuum directed to the station. It consists of a transparent display to set input and other crucial settings. Zhongli SMD soldering and desoldering station temperature can be done by up and down the adjustment buttons. This system is specially designed for lead-free soldering. What I Like/Dislike about Zhongli: Also remember when desoldering by any of the methods, always apply additional solder first. The flux in the new solder helps the old solder flow better.

The Yihua 948 product is a blend of both a soldering and a desoldering station. It is a product of the Yihua manufacturers who are professionals in welding and soldering equipment and falls among the best desoldering stations. From RS PRO, this desoldering station is ideal for desoldering all kinds of components, and includes a vacuum for the easy removal of residual solder. The unit features a microprocessor which provides accurate temperature control, allowing for constant and consistent heat. It also features a ceramic element that provides high performance and fast heating. Its power station is double of their first production and can perform a faster and more efficient job. It is one of the best desoldering stations.

Remove the braid. The braid will be very hot at this point, so make sure not to touch the braid itself, only the spool.There are tons of Desoldering stations available in the market. Therefore, finding the best desoldering stations is challenging, especially for a beginner. So to find out the best options, I decided to undertake extensive research. Removal of components that are sensitive to heat, e.g. transistors, scr, IC.s etc.it is a good idea to use a heat sink clip on the leads. Be careful when repairing devices that contain charged components (batteries, capacitors, etc.). The desoldering braid can easily cause short circuits. If you do not have a desoldering braid at hand, you can also use the braided shield of a BNC or NF cable, which usually works very well. Desoldering gun or iron?

Each of the options has its benefits. Desoldering guns easily reach high temperatures, which makes the soldering process faster. Nevertheless, hot air can heat the unwanted parts. By using desoldering iron, you need to be very accurate to remove only the needed solder. What do you do if the solder won’t melt? It is a product of the Aoyue manufacturers who have been in existence since 1962 producing various original electronic and mechanical engineering products. These features include a desoldering station, a desoldering gun, a vacuum cover, a desoldering gun holder, a power cord and a lot of other added accessories. It has a voltage of 110 and weighs up to 11 pounds. Release the plunger or bulb. Some desoldering pumps have a release button so that you don't have to hold it the whole time.You don't mention it, but heating the component lead (which usually has more mass) is preferred first, then move to the PCB trace. That will reduce the risk of extracting the plated through hole (PTH) when you remove the component. (That is, of course assuming you want to reuse the board.

You may wonder what are these things? Well, these are the basic tools an electronics guy needs in his lab to properly play with electronics. You can call both of them desoldering tools.Using a heat gun is another way to remove solder without the use of a soldering iron. Basically, it heats up the solder enough to be able to remove the components. Using a hot air station is a slightly more professional and expensive way of doing this, as it is basically a heat gun specifically meant for desoldering. If you don't have one of those though, here's how you can use a heat gun to desolder components: Pros: Desoldering pumps come in a wide range of styles, from handheld pumps to electronic, heated guns that require no iron to use. They are great for reworking small parts and getting solder out of pin holes. Removed components can be reused. The design is excellent, and It comes with a crystal-clear LCD. You can set desired temperature settings and monitor variations in practical ways. Dedicated buttons. It has a display mechanism for temperature readings and the temperature is well controlled and regulated.