Fiskars axes have a very flat bit (blade), and all of these axes have much more curved profiles. As a result, it’s harder to do one nice clean motion from one end of the blade to the other.

This invention collects and holds the metallic flakes of the sharpener that build up normally during the sharpening process, which increases the speed of the honing process. Sharpening dull axe edges requires stones with grit. And the grit ranges from 1000 to 3000. So, whetstones with grits ranging from 4000 to 8000 grits are used to polish the knife and sharpen the sharpness. Technique Two: Fiskars Sharpener Any pull-through sharper may leave little wires, burs, or particles of steel clinging to the edge and the Fiskars is no exception. Ideally, leather should be used for stropping, but you don’t need to buy a dedicated strop. I use an old wallet for my axes. You can use an old belt, purse, leather pants – anything.

Fiskars Axe And Knife Sharpener - Pros

I always recommend people learn to sharpen the “proper” way with stones, but it can be hard to beat an easy 60 second sharpen. See how to use the Fiskars sharpener here. How to fix a chipped edge on your axe WD-40 is a common solution, but gun oil, boiled linseed oil, and other solutions work great. I have a full article on every way I know to prevent rust on an axe. One method even includes bacon.

Clean away any dirt or wood fibers from the surface of the axe head, as it will be full of moisture. The Fiskars sharpener is an incredibly versatile tool because it can be used to sharpen both an axe and a knife. In addition, the Fiskars knife and axe sharpener are extremely simple to use. However, with these axes, I know a lot of people don’t bother. Especially with the splitting axes – just keep swinging and sharpen as needed. 2. Maintaining the blade (bit) of your Fiskars Axe I keep an X15 permanently in the trunk of my SUV – all seasons. And in my area, we can go from 40° C to -30° C (100° to -22° F) at the extremes. You can lightly run the edge through the sharpener a single time (maybe it comes off). But the best way to clean the edge is through stropping.Here are the three techniques of the Fiskars axe sharpening process. That will help a user decide which is thebest axe sharpener. Technique One: A Large Sharpening Stone I have to admit I was surprised by how well this cheap little sharpener worked. It’s true you can get a razor-like edge with a sharpening stone, but getting good enough to achieve that takes a fair amount of practice.

When you are examining the edge you should see the newly sharpened bevel as brighter steel. Make sure it is a constant depth/width. Any narrow or non-shiny areas should be sharpened more. A rolled edge is when the fine sharp point of the blade gets bent, or “rolled” to one side. It may not even be noticeable at a glance but if you touch the sides of the blade edge you will feel a thin “wire” or “lip” of metal off to the side, right at the tip. In the case of sharpening an axe, Fiskars needs more attention. The Fiskars axe is quite special compared to a normal axe. Fiskars axe does not support the DIY sharpening process that much. So, theFiskars axe sharpeneris the solution. What is the Process of Sharpening a Fiskars Axe? While most of a Fiskars axe is fairly indestructible, the cutting edge will dull with use and can chip or roll. It’s a fairly common criticism of Fiskars. The 30-degree flat grind edge is sharp but more delicate than a convex grind. Combined with a bit softer steel and you are going to have to do some sharpening. The easiest way is to simply wipe down the head with WD-40 after using the axe. It will both clean away dirt and residue and provide a light oiling at the same time.

Customer reviews

The wider angle will be stronger and more supported, withstanding more impacts without chipping or rolling. This wider second bevel won’t be as useful for tasks like carving, but that’s not really what Fiskars are good for anyway. It will still chop and split well. Sharpening a Fiskars axe requires a few tools to make its blade sharpen. But the basic solution is to use a sharpener. Simply slide the blade into the right slot and roll it a few times to restore the blade’s optimal cutting bevel. This handy little woodland companion features optimum sharpening angles for both Fiskars axes and knives, as well as an easy-to-use mechanism.

The Fiskars machining process produces a series of fine grooves running along the blade that is exposed once the coating starts to wear off. These grooves can be a moisture and rust trap if not cleaned regularly and protected. Oil the head to stop rustSharpening your favourite cutting tools methodically can take up to an hour. Instead, someone might simply polish his axe blades using this Fiskars sharpener. There’s no struggle with the ceramic roller because it sharpens at an exact 30-degree angle. Moreover, the user’s fingertips will never be in danger in this process. But still, a user can gain good knowledge abouthow to use the Fiskars axe sharpener. Technique Three: Smith Diamond Flat Sharpeners