Shot blasting uses a stream of steel shot directed at an object to clean or treat metal. There are two types of shot blasting; wheel blasting and air blasting. There isn't a huge difference to the customer between the two types, and we can help you decide which process is going to be the best for your project. Sand blasting uses sand as the abrasive media being blasted at high speed against the part with sand blast cleaning equipment. Most of the equipment used on oil and gas fields, including drilling operations, goes though shot peening to increase fatigue life. Sa2: Thorough blast cleaning – When viewed without magnification, the surface shall befree from visible oil, grease and dirt, and from most of the mill scale, rust, paintcoatings and foreign matter. Any residual contamination shall be firmly adhering. Although it is considered an expendable abrasive, it is commonly used in blasting cabinets across the country.

The generally accepted industry standard is 4 hours after completing the blasting process with the caveat that ‘all surfaces to be coated should be clean, dry and free from contamination’. Substrate temperature should be at least 3°C above the dew point and always above 0°C. Application at ambient air temperatures below 5°C is not recommended. The maximum air and substrate temperature for application is 50°C providing conditions allow satisfactory application and film formation. If the air and substrate temperatures exceed 50°C and coatings are applied under these conditions, paint film defects such as dry spray, bubbling and pinholing etc, can occur within the coating. Allowances need to be entered before starting the peening process. The common tolerance for this process is about 0.05 mm. A blast hose, deadman handle and venturi design blast nozzle to deliver the abrasivemedia stream to the substrate. KUE Group has over 46 years’ experience of surface preparation and corrosion protection. This means that we were leading the development of grit blasting boiler pressure partsand turbine components well before it became the industry standard. Experience leads toa safer, more reliable, and more accurate project approach. It also means confidence andpeace of mind for our clients.

Contact Us

The shot peening process is recommended for medium production volumes with a high level of automation. Howeevr, due to the fairly fast processing time there is the potential for high production volumes with some materials. Different mechanisms can be used to provide the high velocity shot. Mechanism include compressed air, where the shot is injected into a high velocity stream of air. This gives the shot the required velocity.

We offer a complete range of abrasive shot blast cleaning services, including: Shot Blasting & Painting

What you must do

Incorporating leading coating specialists Lithgow Saekaphen Ltd, KUE Group can advise onthe best procedure for your project or include a protective coating or lining service. Over the last few years environmentally friendly media options have become available, and things like walnut shell and corn cob offer a green alternative for many jobs. An in-depth discussion of all these media choices could easily fill a book. Keep in mind that many of these options have a range of sizes available, so you can fine tune not only the media, but the grain size as well. As you can see, shot blasting services are a great way to remove rust, paint, and other contaminants from your metal surfaces. It’s also a great way to improve the appearance of your equipment and machinery. Whether you’re an industrial business owner or just someone who wants to do some home repairs, shot blasting is a great option! C) Steel surface on which the mill scale has rusted away or from which it can bescraped, but with slight pitting visible under normal vision.

Surface hardening of gear meshing surfaces is done by shot peening for those application where work stresses are not high.Shot blasting uses a stream of tiny steel balls to clean steel parts. The metal balls are blasted at high velocity against the part. This method is often used to prepare parts for painting or powder coating, remove unwanted paint or rust, and prepare the surface for new paint or powder coating system. Sandblasting , also known as abrasive blasting , is a technique used by sand blasters to clean, prepare, or etch surfaces by propelling fine particles at high speeds. It involves using compressed air or a specialised blasting machine to forcefully propel abrasive materials, such as sand, glass beads, or walnut shells, onto a surface. Grit blasting is fast, efficient, and effective. Within the industry, it is recognised as having the best ratio of time taken to required surface cleanliness. For end users and clients, this means reduced downtime and, consequently, improved productivity. Therefore, in terms of ROI, grit blasting is an excellent choice. Sintere d aluminium oxide (or FastBlast, and or Sinterball) is heat-treated aluminium oxide which looks like tiny ball bearings. These ball bearings are much denser than the standard aluminium oxide grains, which means that they hit harder and remove more granite each time they hit the stone when compared to standard aluminiumoxide (which is why we call it FastBlast). The other advantage of FastBlast is its extended life over standard aluminium oxide. When the sintered oxide strikes the stone it chips small particles off the side of the ball rather than splitting into 2 roughly equal parts like the standard aluminium oxide. Grit blasting can alter the surface profile of materials, particularly in commercial sandblasting . By adjusting the abrasive material and blasting settings, it is possible to create specific surface roughness or texture required for improved adhesion, grip, or friction.

People require sandblasting for several reasons due to its effectiveness and versatility. One main use is for surface preparation. Mobile sandblasting gives surfaces a thorough cleaning by removing rust, scale, old paint, and surface contaminants. This prepares the surface for painting, coating, or bonding. Additionally, sandblasting is needed for coating removal, stripping off existing layers of paint or varnish from surfaces. It restores worn or damaged surfaces by removing old coatings and preparing them for a new application. Now our standard aluminium oxide is probably not standard at all when compared to what other suppliers are selling,as all of our aluminium oxide grit is 'virgin'. This means that our grit has only ever been grit and is not material reclaimed from aluminium car parts etc. Our aluminium oxide grit should last longer, be cleaner and produce lessdust. The abrasive media is often inexpensive, and in many cases features the added capacity for either recycling or reuse. This often makes it a cost-friendly approach to surface preparation. The shot blasting process uses high-pressure water, abrasive grit, and compressed air to remove paint and rust from metal surfaces. The advantages of abrasive blasting include its ability to remove material evenly from all surfaces of an object, particularly when the object has tight corners or curves.Do not discharge to public sewers, surface waters or ground waters without consulting your regulator. You may need a discharge consent or other authorisation. For further information, see our guidance on discharges to water and sewer. Good practice Reduce your air emissions If you have a permit, licence or registered exemption you must comply with its conditions. Your permit may contain conditions relating to your levels of noise or air emissions. You can be fined or even sent to prison if you do not comply with conditions. Prevent nuisance