So today we’re going to take a look at some of the best NES and SNES controllers for emulators. We’re going to look at the AGPTEK Wireless Classic Controller, the Suily USB Retro Gamepad Controller, and the iNNext Retro USB Super Controller Gamepad. We’ll discuss the features of each controller then offer a comparison of the three. Why Use an Emulator Controller? It’s an issue where the gamepad is not being recognized by Windows 10. You’ve run the Hardware Troubleshooter, restarted the computer, yet the issue still persists. So what’s the next move, then? Well, we’re going to talk about a number of ways to get this problem under control. 1] Update the driver

The feel of the controllers are sturdy. They’re lightweight, but the buttons are responsive, springy, and do not seem to have any dead zones. The start and select buttons are made with a durable rubber material that is a bit difficult to tell when it’s fully depressing, although that was an issue that the original NES controllers had too. I then carefully removed the USB connectors. They're hard to remove because of the soldered tabs on either side, when I tried to heat those tabs up while lifting up on the connector the whole pad underneath the tab delaminated from the board and broke off. After that, it was just a matter of either desoldering the connector's pins from the board or snapping them off, I recommend keeping the pins on at least one connector so you can use it in later steps to map the pinout of your usb cables.Finally, I connected one of the USB hub's connectors to the keyboard controller's usb cable, and using the multimeter mapped out which pins of the keyboard controller connected to which pins on the connector. I then removed the cable and soldered a short piece of ribbon cable between the keyboard controller and the first port on the hub, matching with the pins that the usb connector would have been connected to. So if you’re a gamer who likes classic titles, then you can benefit from having a retro USB controller on-hand. Some models are wired and others are wireless. Wireless models typically require a USB dongle attachment but some brands have Bluetooth compatible controllers. If you have a Bluetooth controller then your computer or smartphone will have to be capable of Bluetooth connectivity.

Going a little more extreme, it's easy to imagine cutting an entire rectangle out of the top of the board, removing the chip area completely and giving a lot more vertical breathing room for parts to fit in. This would make for a lot more smaller traces to solder, however, and you would need to be careful how much of the board was removed above the select and start buttons.

I put a drop of hot glue on the repositioned capacitors for the USB hub to prevent them from shorting out, and some clear nail polish in the cut traces on the controller board to guard against anything causing them to short together. The case of the hub I used was held together with a single screw, the case lifted apart to reveal a single board. For the retro purist, the ideal way to play via an emulator is with a system’s original controller. Fortunately, there are some low-cost adapters available that can make that possible. Mayflash offers adapters that allow you to connect your SNES, N64, Gamecube, Wii, PS2, and Saturn controllers to your PC via USB. For the most part, these work just like using an Xbox One controller and can be easily configured across emulators. When you start cutting traces, make sure to cut any connection between the buttons and the chip at the top of the board. Otherwise you'll end up with weird issues where one button press can fire off multiple buttons because a circuit gets completed through the chip. It would be a good idea to remove the chip altogether but I didn't have a soldering tip for this and couldn't find another good way to do it.

Your gamepad not being recognized can be fixed with a simple adjustment of the power management settings in Windows 10.

Available exclusively for Nintendo Switch Online members to purchase!

So, which controller in our round-up is the best? A is always the case, the answer to that question depends on what you need. That includes the modern controllers you already have, but they have a major flaw that makes them less than ideal for retro gaming. Specifically, they tend to have mushy D-pads. Suily made a few minor controller modifications, specifically by adding etching to the red "B" and "A" buttons. Of course, the biggest change is the somewhat short 5.6-foot cord, which ends in a standard USB-A plug for compatibility with Raspberry Pi, Windows, Mac, and Linux. You'll have no issue diving into your classic NES library, and enjoying favorites like Super Mario Bros., The Legend of Zelda, Ninja Gaiden, and so many more. For the most part, these tips should do the job. However, should they fail to work, then the best means of moving forward may very well be to get a new gamepad. The drive I used was a simple plastic casing with a row of tabs along the sides on one half of the case, and a long segmented slot for the tabs on the other half. I got a small screwdriver between the halves and carefully levered them open. Since I wasn't going to do anything with the case afterwards I wasn't concerned when I broke a bit of the slot while opening it.

The real benefit is that they can be used for more games. You can play both NES and SNES games with the more complex button layout. The manufacturers also offer a generous 6-month replacement warranty so you can get a full replacement if there are any manufacturer errors. Final Verdict Emulator controllers plug directly into your computer and let you play for favorite games like they were meant to. Players who favor the traditional 2 or 4 button layout and d-pad on the left will probably feel a lot more comfortable playing with an emulator controller. The best emulator controllers have a similar layout to the original controller and mimic the feel of playing with a classic joypad. Let’s face it, if a computer has enough ports, we’ll plug a host of things into the computer and never remove them even when they’re not in use. Starting with the AGPTEK Wireless Classic Controller, these controllers are an excellent choice if you want wireless retro gaming. The wireless signal is strong and the battery lasts for a very long time. You can charge them while you play so you never really have to worry about running out of batteries. These controllers can also be used as a generic gamepad for playing PC games on a client like Steam. While making connections I stopped at several points (after connecting pairs of wires) to test the buttons that should be enabled. This will prevent you from getting everything connected up before realizing there is a problem. One of the rubber button pieces from the shoulder buttons worked to complete the button connections for testing.

Best way to use original controllers with emulators

The Suily gamepad is likewise designed with only two face buttons. AS such, you’ll only be able to play games that have a 2-face-button layout. For example, you won’t be able to play Super Nintendo games with these controllers, but you’ll be able to play games for the original Game Boy and Game Boy Color. The Retro-Bit Official Sega Saturn USB controller is a reproduction of one of the most respected controller designs in history. The original Genesis six-button controller was already well-loved, but the Sega Saturn version refines it into something even more comfortable. So whether you want to play Genesis or Saturn games, the Saturn controller is the best choice overall. The original SNES controller design was already great, but the SN30 manages to maintain what made it special while giving it the right amount of polish for modern gamers. The old-school semi-transparent plastic is a nice touch. However, emulators do have one downside. Most classic games are not designed to be played on a keyboard and mouse or with a touch screen on the phone. Thankfully, there exist emulator controllers that you can use to capture the original experience of playing with the original console. These USB-connected controllers are designed like the originals and most emulators nowadays have some form of third-party controller support. Having a wireless controller is a nice modern convenience, but the best latency and responsiveness are still to be found with wired controllers. Many of the wireless controllers you can buy also let you use a wired connection, but if you're only going to use it in wired mode, why pay for a battery and Bluetooth radio you'll never use?