The Ruida RDC6442S features a USB interface, which allows for easy transfer of data from a computer to the controller. It also has a dedicated DSP processor, which ensures that the laser head moves smoothly and accurately during the cutting and engraving process. Figure 7.2-1 Output Example Chapter8 Human-Computer Interface Operating Instruction Panel and Keys The Operation Panel Well, that’s because you can easily miss what these LEDs are, because right down the center of the box, Pulse and Test buttons work, but LightBurn does not - It's possible the Min Power is too low. Change the Power Min (%) setting in the layer to at least 10%, and make sure the Power Max (%) is 10% or higher, then run a test.

the power supply can deliver a maximum number of milliamps depending on the tube that it’s trying to control. Ruida RDC6332M hybrid cutting controller is a hybrid cutting system based on the proven RDC6332G co2 laser controller, which is specially developed to combine the processing of sheet metal and non-metal cutting. Based on this co2 laser DSP controller, it can realize metal cutting and non-metal cutting. Two-way independent digital/analog interface, the software can be adjusted respectively, convenient for double laser heads control; Dedicated RF laser control interface Compatibility: RDWorks is compatible with a wide range of laser cutting and engraving machines, including those from Ruida, Trocen, and Starfire, as well as many other brands. On-board system encryption control, onboard parameter storage, and file storage capacity of up to 256M

Advantage

After the “Def Fact Para” is selected and the Enter key pressed, the “Successful Recovery” dialog box will pop up to prompt that all manufacturer parameters and user parameters are recovered successfully. You can return to the previous menu by press the Enter key. Auto Focus Exactly!! I typed in 1.2 INCHES for the move and the table moved down 1.2 mm and the display read 1.2. But the display is in inches. see the problem yet? after the 1.2 mm move the display should have read 1.2/25.4=0.0472 Hard-spacing Protection: it is used for whether the hard-spacing protection of this axle is enabled. Maximum Speed: it means the maximum limit of motion speed that this axis can bear. This parameter has something to do with the driving force of motor, the inertia of motion axle and its drive ratio. For example, the typical value is 200~500mm/s. All outputs are isolated through the optocoupler, and 500mA current for each, OC gate output, each can directly drive the 6V/24V relay, led lamp, buzzer etc.

Can't cut through my material, but others with the same exact laser can - Bed alignment, mirror alignment, material, speed, and power can all be culprits, but I have run across situations where someone was using settings in inches and their friends were using mm. The Ruida RDC6442S is an upgrade from the previous RDC6442 controller, and it comes with advanced features such as a larger screen display, more memory, and improved software compatibility. It supports multiple software programs such as RDWorks, LaserCut, and LightBurn, which provide users with a user-friendly interface for designing and executing laser jobs. RDWorks supports a wide variety of file formats, including common image and vector formats such as JPG, PNG, DXF, and AI.For more detailed pin description, see the Chapter 4: Description of Interface Signal for Controller. And, the pulse signal can be falling edge valid or rising edge valid. The default setting is falling edge valid. One of them is via a local area network an Ethernet system. One of them is via a direct link between the computer and the USB input. One Key Setting: This is one recommended cutting parameters settings button; it is not a parameter, there are several groups of parameters under this button, which is convenient for selection. The input signal end of step-servo motor driver employs the opto-isolator technology. For the step pulse signal, some isolate the side OC diode from cutoff to conduction (e.g. the valid falling edge of pulse signal inputted from the diode minus end) and some do so from conduction to cutoff (e.g. the valid rising edge of pulse signal inputted from the diode minus end).

It may not have as many advanced features as some other laser cutting and engraving software programs on the market. Please Note: DO NOT carry out a Factory Parameters Reset! Transcript for the Ruida Controller In Brief After modified the configuration parameters in the manufacturer parameters, such as directional polarity, control mode, laser type and laser PWM frequency, the system should be reset. Such a modification can function upon

Ruida 6432 Controller for CO2 Small Laser Machine

parameters. If so, the setting will become ineffective and the system will automatically cover the parameters with the axis parameters. Current work time: To forecast the running time of the current file (the current file No. is showed on the main interface), and the time is accurate to 1ms. The Ruida DRC6445S and DRC6445G are both laser controllers used for CO2 laser cutting or engraving machines, but there are some differences between them. Y Frame over size Work Paused - The design is too large or too close to the front or rear edge of the bed. Try centering the design on the bed or reducing the size of the design. Now, draw a box similar to the original, but make it 100 x 100, or 200 x 200 (mm), set the Min and Max power low to start, but high enough to make a mark, and run the job it on a piece of scrap material. Measure the result as accurately as you can.