Motast Wireless Earbuds Headphones, Wireless Headphones Waterproof IP7 Bluetooth 5.1 In-Ear Headphones, Bluetooth Headphones with Mic, HiFi Stereo Sports Headsets with Deep Bass for iPhone and Android

Product Information

Step 1: Open the Connection Settings on your device. This can usually be found in the Settings app.

press L and R earbuds for about 5 seconds to turn off them, in off status, long press L and R earbuds for about 20 seconds, the earbuds will start to restore factory setting Once the reset button is located, press and hold the button for 10-15 seconds. You may hear a small beep or a single tone. If you don’t hear the tone, press and hold the button again. Continue to do this until you hear a tone, indicating the reset is complete. Depending on which operating system you are using, you might need to go into your device’s “Settings” and toggle the Bluetooth switch on and off.

Precautions When Connecting Bluetooth Earbuds

Press mfb (multi-function button) continuously for 2 seconds to turn on, then turn on until the blue light can be seen. First, make sure that your earbuds are turned off. If they're not, press and hold the power button until they turn off. Once they're off, press and hold the power button for about 10 seconds. This will put your earbuds into "pairing mode." Press any one of the multi-function buttons on the left and right sides for 2 seconds and the power will automatically turn on, then you will hear a prompt tone for booting. The specific buttons you hit (and how long you press them) will change depending on the earbuds, but the procedure on how to put Bluetooth earbuds in pairing mode is always as straightforward as the following:

Select the two earbuds and they should connect automatically at the same time. If that doesn’t work, try putting the earbuds in pairing mode. Generally, you will do this by holding down both power buttons simultaneously. The blue light will flash for about 4 times then your headset is factory reset and all pairing information is deleted. You should then see the earbuds appear in the list of Bluetooth devices on your device. Select the earbuds from the list and they should be connected. If that doesn’t work, then you may need to put the earbuds into pairing mode.Well for Jabra I'll discuss method with three different headsets because due to different buttons you might want better idea. When it comes to Bluedio due to different products in the market it could vary just with volume or power buttons. If that doesn’t work, try resetting them. This can typically be done by pressing and holding the power button for 10-15 seconds. Once your earbuds are reset, try to pair them again. Please use the mobile phone adapter to charge the charging compartment, you can also use the computer USB cable or other USB interface charger for charging. Once turned on again just go to the Bluetooth settings of your desired device and pair with Mpow Headphones.

Delete the headphones from your cell phone's paired list, restart your phone and re-pair the headset. After inserting your earbuds, close the lid of the charging case. Open the case after 5–6 seconds have passed. The Bluetooth pairing mode will be automatically entered by the earbuds. Put them in your ears and hold both touchpads for a few seconds until pairing mode activates them if they are already attached to another device. Conclusion Delete Bose headphones from Bluetooth list of your device and then the headphones are ready to pair again. Repeated charging and discharging the headset will cause the battery performance to decrease over time, which is normal for all rechargeable electronic products.Once both headphones are in pairing mode, they will be discoverable and you should see them listed as “Power Q20” on the Bluetooth device list of your source device. Choose the two power Q20 devices and they should be successfully paired together. How do you pair both earbuds together? Because the Bluetooth headset signal cannot be transmitted in water, swimming and diving will cause the signal to be disconnected or interrupted.

If your headset stops functioning properly then you have to go for factory reset which will delete all paired devices. When you're trying to set up your Bluetooth devices, they might not connect if their range is too far apart or they aren't in pairing mode. If this problem persists despite multiple tries on both sides of the connection process, try resetting them! How do you reset Bluetooth earbuds ? If you have volume button along with power button - then you need to press and hold power as well as volume +/- button simultaneously for up to 10 seconds. First, make sure your earbuds are turned off. If they are on, hold down the power button for 8-10 seconds to turn them off. Meanwhile for Jabra Street2 or BT3030, firstly turn off the headphone and press as well as hold the Answer/End button until the light flashes from blue to solid blue and then to purple. Once done your device is reset.Donerton Power Q20 Pro Headphones [pdf] User Manual Power, Q20 Pro, Q20, Headphones, maggiechiu527, motasttech If you have call as well as volume button along with power button - then you might need to perform combination of power and call or call or volume button by pressing them for up to 10 seconds.