Joined in 2023 
82 
63 About this deal
Decontamination of the paint surface is critical to proper auto care for a multitude of reasons. To begin with you want to remove all contaminants before polishing, so you can work on a clean canvas rather than dragging tiny contaminants across the paint during the polishing phase. Using the CarPro Polyshave Decontamination Clay Towelyou can remove surface bonded contaminants and use Iron X to remove anything below the surface of the paint as well. Each time you brake, friction from your brake discs and brake pads causes a cloud of sizzling hot iron brake dust to melt onto your car paint. The iron remover will partly dissolve these dust particles, which in turn will make it faster and easier to remove them with your clay bar. We worked in about 2’x2’ areas gently rubbing our “gold bar” in a crosswise pattern: up/down and side to side, constantly keeping the surface saturated with lubricant. After clay-barring a section, we gently wiped it dry for inspection. We had to use extra towels, one didn’t cut it. The clay bar was folded and kneaded when needed to make sure its working surface remained sufficiently clean. Car surface decontamination by means of claying or clay-barring is often skipped or overlooked. That’s because most people don’t know or misunderstand this vital step in the car exterior detailing process.
The Autoscrub Fine Grade Towel is easy to rinse off when it’s dirty or when you’ve dropped it (again). That’s a big advantage in our book! It’s such a waste and extremely frustrating that you have to dispose of a classic clay bar when you drop it. This clay towel also outlasts a clay bar up to 10 times. Though clay barring has lifted professional car detailing to a higher level since it was invented in Japan in the 80’s, its benefits are still far less well known by the general public than the advantages of polishing and waxing. This is most likely because it’s not a final, spectacular stand-alone part of detailing. Nevertheless, it is essential to clay bar your car before the polishing process or before applying any form of paint protection. Not only does it make polishing easier and faster and protective coatings more effective, but most of all it greatly reduces the risk of marring your paint (or worse). If you don’t want to clay by hand, it’s better to just skip this step and use a polisher with compound right away, followed by a fine polish to remove the swirls and scratches caused by the compound stage of course.
We used Adam’s Detail Spray that comes with the combo for lubrication. We love this product, it smells great too. We rinsed the mitt as often as we could, then again dipped it in soapy water, and moved on to the next panel. And so on… The Atomiza Clay Towel is designed to replace the clay bar in the decontamination process. By using a special kind of polymerised rubber (bonded to a microfibre towel), it is able to dislodge bonded contaminants when rubbed over exterior automotive surfaces, and thus mimic the result that a clay bar produces, i.e. perfect smoothness. Furthermore, it does this without needing to be warmed up first (or kept warm during use), and it can be rinsed completely clean with running water, meaning that it not only has a far greater life expectancy than a clay bar (up to five times as long), but also does not have to be thrown out if you accidentally drop it. However, perhaps the biggest benefit the Atomiza Clay Towel offers is a significant time-saving; on a like for like basis (i.e. mild clay vs. fine towel) it gets the job done much faster. Mothers Speed Clay 2.0 is a game changer when it comes to ease of use and ergonomics. It does what a clay mitt or clay towel does but it distributes pressure more evenly like a clay bar does.
Wash your car as normal (use a car shampoo and not washing-up liquid, it can damage the paint). Make sure your bodywork is still damp before beginning to clay bar it. Features a microfibre cloth on one side and a Full Face Patented Advanced Polymer Rubber layer bond to one the other. With the lubricated clay towel & surface, start rubbing the clay towel over the panel you are treating until it glides smoothly. Pass the Clay Cloth over the wet surface. The Clay Cloth should be turned over or rinsed regularly to reduce the risk of removed contamination scratching the paintwork
The Atomiza Clay Towel should be used out of direct sunlight, on freshly washed bodywork and glass that is cool to the touch. For best results, wash and rinse your car as usual and then, working on one panel or window at a time, spray both the surface to be treated and the polymerised rubber face of the towel with a suitable lubricant (we recommend using Auto Finesse Glide, although other clay bar lubricants may also be used). Next, fold the towel in half and then half again (with the rubber side out), then lay it on the panel and, using light pressure, begin rubbing it gently in straight lines in all directions. Initially you will feel some resistance (as the towel encounters bonded contaminants), but gradually this will ease until the towel glides freely, indicating that the contaminants have been fully removed and perfect smoothness restored. Repeat these steps until all of the bodywork and glass is done, and then rinse the whole car thoroughly and dry it off. It’s important to keep this tool well lubricated to minimize the risk of scratching the surface. We used Mothers California Gold Instant Detailer spray which works best.
The vast majority of customers are over the moon about this clay combo, but a few complain that it is not harsh enough to remove heavily contaminated surfaces. We completely get that: we advise to start with a medium grade clay bar if your car paint has been neglected, then switch to the fine grade. The difference was night and day! Gone was the rough gritty surface. It felt smooth as silk. In fact, as you are rubbing the mitt, you can feel surface resistance diminishing with each pass. In no time, our red test car’s clear coat looked and felt rejuvenated! Rinse, soap, lube, caress… This ain’t work, it’s therapy! Important: If you accidentally drop your clay bar (yep, we know the feeling), throw it in the trash can! It will be littered with dirt and grit. Believe us: It will scratch your car for sure, it’s just not worth it. Grab a new clay bar instead. I find that when claying a car (either towel or normal clay bar) you will always get some form of marring afterwards and I recommend that you always follow up with a polishing step afterwards. How to Use a Clay TowelEven though it takes significantly longer to complete a car, my personal choice is still with the traditional style clay bar as I find that it will remove the more stubborn contaminants more effectively and I have more control in terms of being careful with potential marring. Use this Fine Grade Clay Towel during the wash process or during a standard decontamination process. Unlike clay bars, synthetic clay towels allow you to rinse off contaminants after using providing you with a product that will last. Great value from a trusted household name since 1973. Highly recommended and it won’t break the bank!
CarPro Polyshave Decontamination Towel is a simple and fast method to remove contaminants from the surface of exterior automotive finishes and glass.With advanced Rubber Polymer Technology bonded to a 12" x 12" Microfiber towel you have another excellent option from CarPro for eliminating the need for detailing clay. No, a clay bar does not remove scratches. A clay bar, mitt or towel is designed to only remove the tiny car surface contaminants that cause the roughness you feel when you gently stroke your car paint. To remove scratches, use car polish . Car polish can be used manually or with a car polisher . Should you Clay by Hand or Machine? The red car we tested this on had been parked under a maple tree for years with only scarce car wash visits and had never been clayed before. After having thoroughly blasted it with a pressure washer and washed it, we rolled up our sleeves and got to work. Do the plastic bag test: Before you start claying, gently rub the car surface with a plastic zip bag wrapped around your hand. You will feel roughness and hear a scratching sound. After you’ve done a few passes with the fine grade clay, repeat the zip bag test. It should now feel smooth as silk, without the scratching sound.
Subscribe To Our Newsletter. It's 100% Free!
Can be used with a water or pH neutral car shampoo (preferred) the vehicle paint and you can remove all surface embedded contamination faster and more effectively than a clay bar. First wash your car very thoroughly and park it somewhere in the shade. Hot car paint is too soft to clay bar and would easily scratch. Always work with an abundant amount of clay lubricant to prevent scratching up your car surface. Don’t use soap of any kind as a lubricant, it’s not as effective and it will make your clay bar brittle and fall apart. Using a clean microfiber towel, wipe off all remaining clay lubricant and dry the decontaminated panel before moving onto the next.
Great Deal 
New Comment